 |
CK_PACK 1 ContentsTo use these modules you need a Registered Version of SynthEdit Ver:1.017+Guide CPU readings from Intel Pentium4 1.5Ghz For details on CPU readings and comparing with other systems/modules see:- CPU Guide |
Signal Processing |
 X_Mix: CPU 0.075% / 0.105% Cross Mixes 2 signals to 1 output 5 mix modes (Balanced, Analogue, Peak1,2,3) |
 Warp: CPU 0.080% / 0.150% Signal Warping, changes the waveshape PreGain(adjusts the input level) Warp level(+/- 100: 0=unchanged) Numerous modes(20), Bypass and Off modes For Tonal shaping/Saturation/Distortion etc |
 Clipper: CPU 0.100% / 0.120% Signal clipping/hard limiting: Pre_Gain(adjusts the input level) Clip modes (Gain, Limit, Reflect, Digital) Bypass and Off modes |
 Panner: CPU 0.100% / 0.110% Signal panning: mono input -> stereo output Volume (2 modes Linear, Analogue) Pan modes (Balanced, Analogue, Peak1,2,3, Edge) |
 Multi_Panner2: CPU 0.120% / 0.140% Operates like a Multi Channel Mixer Independent 2x Mono inputs -> combined Stereo output Volume - 2 modes Pan - 6 modes |
 Stereo_Balance: CPU 0.090% / 0.120% Stereo in->stereo out Volume - 2 modes Balance - 3 modes (Linear, Analogue1,2) Swap outputs option (great for FX) |
 Contour: CPU 0.000% / 0.090%(typ) Modifies the response of a signal (0-10v): 10 modes  Contour_Plus: CPU 0.000% / 0.100%(typ) As above PLUS output re-scaling to Low/High range: 10 modes Contour Shapes 
|
Utility |
 Host_BPM: CPU 0.080% Provides host BPM/tempo value |
 1x_Choice_to_1: CPU 0.075% / 0.075% 1x Multi-Choice switch with Level control Create your list of 'choice' signals by linking to the 'Add Signal' (just like the SE_Switch modules) |
 2x_Choice_to_2: CPU 0.090% / 0.095% (All 2 active) Independent 2x Source Multi-Choice switch with Level controls to 2 Destinations |
 1x_Choice_to_1_Plus: CPU 0.070% / 0.100% (Limit=On) 1x Multi-Choice switch with Level control PLUS output range limiting |
 2x_Choice_to_1_Plus: CPU 0.075% / 0.120% (All 2 Active + Limit=On) Independent 2x Source Multi-Choice switch with Level controls PLUS output range limiting |
 Pitch_Volt_to_Khz: CPU 0.000% / 0.140% Converts Pitch(1v/Oct) signal to 1v/Khz A 1v/Khz system generally uses less CPU when modulated |
 Pitch_Volt_to_Time(s): CPU 0.000% / 0.170% Converts Pitch(1v/Oct) to Time(s) e.g. WaveGuide: match Delay time to Frequency |
 Time_to_OscPitch: CPU 0.000% / 0.460% (1v/Oct mode) : 0.170%(Khz/Hz mode) Converts Time(s or ms) to Osc_Pitch signal(Oct, Khz or Hz) e.g. matching Oscillators to Host BPM/Tempo |
 SE_Osc_PW_Adj: CPU 0.075% Use with SE_Osc to convert Pulse waveform to a Balanced(+/-5v) Pulse Modulator signal |
 SampleRate: CPU 0.000% Provides System sample rate, various references and PI |
 Auto_Active_Switch: CPU 0.000% During the Delay Off period CPU 0.050% Auto control over CK_Modules with Active Switches In AUTO mode: Monitors the Input - when stops (0.0v Not streaming) shuts down any linked modules after the Delay Off time Delay Off Switch(ms) allows time for linked modules to stabalise before shutting down Override On/Off options allow instant user switching of all linked modules instead of AUTO |
Modulation Source Modules |
 Mod_Osc - Mod(ulation)_Osc(illator): CPU 0.130%(typ) / 0.260%(typ) Oscillator specifically for providing Modulation signals (e.g. LFO etc.) Pitch(Oct, Khz, Hz - 64bit precision) Phase/Pulse Width Sync(Hard) Hold function 19 waveforms: Sin, Sinic, Tri, Peak, Dip, Hump, Saw, RipSaw1, RipSaw2 Ramp, RipRamp1, RipRamp2, SharkR, SharkL, Pulse, Rnd, Rnd2, PureSine, Pulse2 |
 Env_HAHDSR: CPU 0.115% Hold, Attack, Hold, Decay, Sustain, Release: Envelope generator Stage times in Seconds: 13 Output Contour modes(*See 'Contour Shapes' above) Volume, Master stage time scaling(Kbd/Vel tracking) |
 Chorus_Driver: CPU 0.140% Provides a Modulation Driver signal for the Chorus Engine modules Pitch(Oct,Khz,Hz - 64bit precision) Sync Phase Waveform(6 types: Sine, Tri, Peak, Dip, Hump, Noise) |
 Chorus_Driver_2: CPU 0.180% Provides 2x Modulation Driver signals for Chorus Engine modules etc. Same Pitch(Oct,Khz,Hz - 64bit precision) Sync Independent Phase Waveform(6 types: Sine, Tri, Peak, Dip, Hump, Noise) |
Delay and Effects |
 Delay: CPU 0.120% / 0.180% (Interpolated) Delay with Feedback: Time(s,ms,samples) *Now supports Sleep Mode when Audio input is 0v* |
 Delay_Damp: CPU 0.120% / 0.230% (Interpolated) Delay with Feedback Damping: Time(s,ms,samples) *Now supports Sleep Mode when Audio input is 0v* |
 2TDly: CPU 0.140% / 0.190% (Interpolated) 2 tap delay with Feedback Independent outputs Time(s,ms,samples) |
 2TDly_Damp: CPU 0.160% / 0.230% (Interpolated) 2 tap delay with Feedback damping Independent outputs>br>Time(s,ms,samples) |
 Stereo_Dly: CPU 0.200% Stereo Delay (Stereo In and Out) with Feedback Normal,Cross feedback modes Time(s,ms,samples) *Note: does not support realtime delay modulation |
 Stereo_Echos_1: CPU 0.160% Typical (Interpolated: 0.170%/0.280% Time+Pan+Vol Mod) Mono to Stereo Echo generator Independent Volume - 2 modes Pan Delay Time(s,ms,samples) Master Time Adjust 4 Feedback & Damping modes |
 Stereo_Echos_2: CPU 0.190% Typical (Interpolated: 0.205%/0.380% Time+Pan+Vol Mod) As above with 2 echo points (taps) |
 1v_Chorus: CPU 0.170% / 0.210% 1 voice chorus engine Pre-Delay(s,ms) Depth external Mod driver input Depth Feedback - 2 modes |
 2v_Chorus: CPU 0.270% / 0.310% 2 Voice chorus engine 2x Pre_Delay(s,ms) external Mod driver inputs Master Depth Voice 1 feedback - 2 modes Independent voice outputs |
Arpeggio (Midi) |
 Classic_Arp: Live based Arpeggio with internal Bpm Clock **Dynamic timing Sync's to first Note of each new chord played** Velocity Modes: Note, Constant Note mode: Each note maintains its velocity as originally played Constant mode: Each note plays using the First note velocity The playing Arp pattern can be dynamically transposed via notes on another channel |
 Clocked_Arp: Live based Arpeggio Synced to an external Clock e.g. for Host BPM Sync (for Hard Beat/Bar sync) |
MIDI |
 Volt_to_Midi: CPU 0.000% / 0.150%(typ) Converts a signal(0-10v) to Midi signals: any CC#, Aftertouch or PitchBend |
 **NEW** Volt_to_Midi2 As Above with 'Step Accuracy' options to create Stepped FX, Glissando bends etc. |
 Midi_4x_Zone Keyboard Zoning, Splitting or Layering Each zone has: Low/High Note Range Velocity fading(4 modes) Zones can overlap Transpose and output Channel |
 Midi_4x_Zone_Plus As above PLUS Program and Bank Select(Msb/Lsb) per zone |
 Midi_Choice_to_1 Choose which of the Multiple_Midi Inputs to route to the output Option for All Midi data or just one Channel  Midi_1_to_Choice Choose which of the Multiple_Midi Outputs the input routes to Option for All Midi data or just one Channel |
 Midi_Splitter Separates Midi Notes from Other Midi data stream 2 outputs Midi_Notes, Midi_Other |
 Midi_Prog_Bank_CC Allows Program, Bank Select(Msb,Lsb), and any CC value to be set on any Midi Channel |
All material on this site Copyright © 2003-2011 Chris Kerry
SynthEdit and the SynthEdit logo are the property of Jeff McClintock